Parts & Accessories
Stan's No Tubes' Presta Removable Valve Core is a replacement valve core for Stan's No Tubes Presta valve stems and Presta valve equipped rim strips.
Your riding doesn’t need to stop when the weather gets cold. Features - Giant road thru-axle trainer axle - Alloy construction - For use on 2017+ Giant road bikes with a 142x12mm rear thru-axle
$20.99 - $24.99
- CNC-machined tubeless valves with aluminum stem nut and valve core wrench cap - Fit for most other tubeless rims and wheel
$5.00 - $6.50
- Strong nylon reinforced PVC for a secure fit - Handles high-pressures; does not rot - 0.5mm thick
The Deadbolt Thru-Axles feature the classic-looking Salsa lever and can be adjusted to return to the desired position when properly tightened. Lightweight, easy to use, and secure. - CNC-machined from 7000 series aluminum - Designed to fit all current Salsa thru-axle frames - For other frames, check with the manufacturer for compatibility and other specifications
$19.99 - $24.99
Booster thru-axle hub spacer kits are designed to give your non-Boost front and rear thru-axle hubs the boost they need to fit any Boost-compatible frame or fork.
$6.99 - $7.99
- Plastic spoke covers in a variety of colors - 300mm cut to fit length - 36 pieces - enough for one wheel - Increases visibility and demands attention
Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability. - No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world. Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.
After years of mountain biking with thru-axles with bulky handles that seemed to strike every trailside obstacle, we needed a better option. Our Lightning Bolt-On thru axles offer a high-quality, simple, lightweight alternative to that bulky handle. Available in a range of sizes that fit both front and rear wheels on all types of thru-axle-equipped bikes. - Lightning is Better—Our front and rear Lightning Bolt-On axles offer a stronger, more durable, lower profile, and lighter weight option to replace your stock thru-axles. - Low Profile—No more bulky handles to strike trail obstacles. Aerodynamic design. - Light Weight—Our axles are internally bored to remove unnecessary material without compromising strength. - Easy to install—Our matching front and rear Lightning Bolt-On Axles require only a standard 6mm hex wrench for easy installation and removal. - Better Tolerances—Manufactured in the USA to the tightest tolerances using aerospace materials and CNC manufacturing. No longer will your axle loosen while riding.
Designed to conform to the center channel and bead locking rim bed, Boyd tubeless tape creates an air-tight seal between the tire and rim bed. - Not as stiff as a lot of the other options, which makes installation a breeze!
$14.95 - $79.95
Make your WTB rims air tight and ready for tubeless use with WTB's TCS Rim Tape. This tape covers the spoke holes and can be used as a lightweight rim tape in any rim. Available in 11-meter (covers 5 rims) and 55-meter rolls (covers 27 rims).
$7.99 - $33.89
Replacement axles for MX-2000 hubs. Size: 14 x 100 x 165mm - Supplier Part: KT-M18F - MPN: 370666 - Front/Rear: Front - Diameter: 14mm - OLD: 100mm Size: 14 x 110 x 180mm - Supplier Part: KT-389R - MPN: 370668 - Front/Rear: Rear - Diameter: 14mm - OLD: 110mm Size: 3/8-inch x 100 x 165mm - Supplier Part: KT-M17F - MPN: 370667 - Front/Rear: Front - Diameter: 3/8-inch - OLD: 100mm Size: 3/8-inch x 110 x 180mm - Supplier Part: KT-M88R - MPN: 370682 - Front/Rear: Rear - Diameter: 14mm slotted for 3/8-inch - OLD: 110mm
Use Stan's Tubeless Valve Stems when you're converting standard rims to tubeless via the taping method. These also have a removable core for easier application of tire sealant. Note: Schrader valve is for non-stepped Hugo rims. If your Hugo rim decal reads: - MAX RIM PRESSURE: 2.8 tires: 26psi, 3.0 tires: 24psi - ERD 615, 622x49.9, 29 in x 52.3mm Your rim has a stepped valve and is not compatible with this Schrader valve.
$14.99 - $25.00
Can be used with Stan's ZTR rims to make them airtight or used as a lightweight rim tape in any rim. A single 10-yard roll will tape five 26-inch rims or four 29-inch rims or two wide road clincher rims. 21mm width fits: - ZTR Olympic - ZTR Iron Cross - ZTR 355 - ZTR Alpine - ZTR Crest - ZTR Alpha 340 (2 layers) - ZTR Alpha 400 (2 layers) - Most road clincher rims 25mm width fits: - ZTR 355 (26", 650b, 29") - ZTR Crest - Crest MK3 - ZTR Arch EX - ZTR Flow EX - Crest S1 27mm width fits: - ZTR Flow EX - ZTR Bravo - ZTR Hugo 52mm - Arch S1 - ZTR Rapid 28 - ZTR Rapid 30 - Arch MK3 30mm width fits: - ZTR Flow MK3
Stan's 3.30/3.30Ti Hub Kit converts Stan's 3.30 front hubs from quick-release to through-axle compatible. Installation is easy—just pull the old ones off and put the new ones on. Conversion kits available in 12mm and 15mm.
Stan's Flow Rim Strip converts standard tubed wheels to tubeless so you can reap the benefits. Going tubeless allows you to run low tire pressure for better traction while drastically reducing the chances of a flat. Stan's rim strips create a tight seal with the tire bead, reducing the instances of "burping." Plus, you won't miss dealing with flat tires and you'll save money on tubes!
Replacement indicator chain for three speed Sturmey Archer hubs.
- Green colored spoke prep remains pliable for adjustments - Helps keep spoke nipples from loosening
Stan's Cyclocross Rim Strip converts standard tubed wheels to tubeless so you can reap the benefits. Going tubeless allows you to run low tire pressure for better traction while drastically reducing the chances of a flat. Stan's rim strips create a tight seal with the tire bead, reducing the instances of "burping". Plus, you won't miss dealing with flat tires and you'll save money on tubes!
WTB's TCS AL valves are aluminum to shed grams, and come in catchy anodized red, black, or blue. A stepped lock nut adds compatibility among various rim drillings, a smooth pump interface makes adding air easy, and a removable core makes setting beads and injecting sealant a cinch. - Presta - 46mm
$9.00 - $53.00
Whisky’s tubeless rim tape is designed to make setup as easy as possible. Elasticity allows for smooth, even adherence while translucency lets you see where the tape contacts the rim. Different widths available to fit almost any rim.
Trainer ready. Keep the ride going by putting your Cannondale on a trainer with the 2-in-1 trainer axle. Where it thrives: The open road, on the trainer What it's built for: Versatility, convenience Highlights: - Fit your Cannondale road bike to any indoor trainer Removable end caps for outdoor riding - Compatible with Cannondale road bikes that utilize Syntace X-12 dropouts
$4.00 - $17.00
Whisky Parts Co. Tubeless Rim Tape.
$85.00 - $149.99
Replacement Freehub body for OOZY Trail R142/135, SPIKE R135/142, or SPIKE DH R150/157 Rear hubs. Compatible with all OOZY hubs and wheels. Compatible only with SPIKE and SPOON wheels (135mm and 150mm) produced in 2016 or later (with SPIKE hubs).
$6.18 - $9.79
- MAX bearings are filled completely with high precision Grade 10 balls for maximum load capacity - No retainer means these bearings have 40 percent more capacity
Stan's lightweight aluminum valve stems are half the weight of Stan's standard brass valves. The secure round base is compatible with most tubeless rims and a perfect fit for all Stan's BST rims. A removable valve core makes adding sealant easy, and these babies fit up to 8mm valve hole. Sold as a pair.
- 6061-T6 aluminum lever construction - Cr-Mo axle - Road 100mm/130mm - MTB 100mm/135mm - 110g
$19.99 - $24.99
Thru-Axle hub adapters allow the use of 100 mm front thru-axle hubs in 100 mm QR forks. -Allows the use of modern thru-axle wheels in forks designed for quick-release compatible hubs -100 mm front hub spacing only -CNC-machined AL-6061
- Replacement steel quick release skewers
Page 1 of 2 Next page