Skip to main content

Filter By:

  • Show More Brands

  • Show Fewer Brands
  • Show More Sizes
  • Show Fewer Sizes

Tools

$145.02
Park Tool has long provided some of the best cutting and machining tools in the bicycle industry. Their 690 Cutting Facers reflect their commitment to maintaining this high level of quality. Please read below for use and compatibility information specific to each size cutter: - 45mm (690): The 690 cutting facer is used on the HTR-1, HTR-1B, BFS-1, and BTS-1 cutting and facing tools. The facer has an outside diameter of approximately 45mm. - 57mm (690XL): The 690-XL is a larger version of the 690 facer for the HTR-1 Head Tube Reamer and Facer. It has a nominal outside diameter of 57mm. It may be used in conjunction with the 788 reamer. It is also used with the 767 Pilot or the 768 Pilot to face only the large diameter headtubes used with, "low profile," ZS-type headsets. - 65mm (690-XXL): The 690-XXL faces large headtubes. It has a nominal outside diameter of 65mm. Use the 690-XXL facer with the 750.2 Centering Cone Adaptor and 789 Reamer or 790 Pilot when facing head tubes with internal diameters of 55.95–55.90mm.
$49.20
Park Tool's 750.2 Centering Cone Adaptor increases the size of the centering cone of the HTR-1 and HTR-1B Headtube Reaming and Facing Sets. The 750.2 will allow you to use the HTR-1(B) to ream and face head tubes designed to accept IS, ZS, and 1.5-inch EC headset standards. Before reaming or facing, make sure you have the correct cutting tool and pilot for the headset standard(s) you are using. Please refer to our product pages for cutters and pilots for this detailed compatibility information.
$30.95
Cleans bicycle chain quickly, easily, and effectively — without the hassle and mess of removing the chain from the bike. The Cyclone uses a large solvent reservoir, hundreds of rotating bristles, and a two-step cleaning process to get chains really clean, improve shifting performance, and extend the life of the chain and other expensive drivetrain parts. - Works with all multi-speed bikes (5, 6, 7, 8, 9, 10, 11, and 12-speed) as well as some single-speed models and e-bikes - Strong magnet at the bottom of the fluid reservoir holds metallic particles scrubbed from the chain - Special wicking sponge draws solvent from the chain as it exits, minimizing drips and mess - Sturdy handle makes the Cyclone easy to use and control - Holds 2 fluid ounces (59ml) of solvent
$29.99
To prevent poor shifting and uneven drivetrain wear, most manufacturers recommend chain replacement at or before 1% stretch. Now you can quickly and accurately determine the wear and stretch of any chain with Park's Chain Checker. Simply insert the Chain Checker’s pins into 2 links, press the swingarm gauge tight, and then check the gauge window for an accurate reading!
$28.95
Park's Mini Chain Brute Chain Tool goes anywhere and features a V-shaped handle, a super-strong replaceable pin, and fine threads to make chain removal and installation a breeze. The CT-5 works on any derailleur chain, including Shimano Hyperglide and 9-, 10-, and 11-speed. It works for loosening tight links, too.
$26.95
Precision CNC machined aluminum tool for the installation and removal of 16-notch external bearing bottom brackets. Featuring updated tooth profiles to optimize the fit between the tool and high performance BB parts. Anodized and laser engraved for easy identification and featuring a ratchet/torque wrench compatible 3/8-inch drive. - 16-notch 39mm OD cups - Fits: Shimano XTR BB93, Dura-Ace BB9000, Token - Added depth to fit Shimano STEPS square drive motor
$26.95
The MT-10, 20, 30 and 40 are high quality folding take-along tools that feature forged aluminum side plates, a mix of hardened and plated tools, and smooth ergonomic operation.
$25.95
Destined to become a classic, the Master Spoke Wrench is an investment cast workhorse poured from the best steel, precisely machined, heat treated for hardness, then polished and plated. The result is a smooth, solid, perfectly balanced steel spoke wrench designed and built to fit perfectly in your hand and provide years of every day service. The SW-20.2 is a three-sided spoke wrench the same size as the SW-0 (black) for .127” (3.23mm) nipples. Weight: 39g
$25.95
Destined to become a classic, Park Tool's Master Spoke Wrench is an investment cast workhorse poured from the best steel, precisely machined, heat treated for hardness, then polished and plated. The result is a smooth, solid, perfectly balanced steel spoke wrench designed and built to fit perfectly in your hand and provide years of every day service. The SW-22.2 is a three-sided spoke wrench the same size as the SW-2 (red) for .136” (3.45mm) nipples. Weight: 39g
$23.95
Park Tool's professional-quality Snap Ring Pliers are made from forged, heat-treated cro-moly steel with a return spring and vinyl-dipped grips. The RP-4 has 1.7mm tips on bent nose blades for larger, internal snap rings. The tips open from 21mm down to 2mm (center to center).
$21.95
Park Tool's professional-quality Snap Ring Pliers are made from forged, heat-treated cro-moly steel with a return spring and vinyl-dipped grips. The RP-3 has 1.3mm tips on bent nose blades for medium, external snap rings.
$21.95
Park Tool's professional-quality Snap Ring Pliers are made from forged, heat-treated cro-moly steel with a return spring and vinyl-dipped grips. The RP-2 has 1.3mm tips on bent nose blades for medium, internal snap rings. The tips of the RP-2 open from 22mm down to 2mm (center to center).
$20.95
Also called a sleeping hub, the Dummy Hub slides into rear dropouts and replaces the rear wheel for chain cleaning and transport. The DH-1 works with all derailleur and 1/8" chain. The unique design allows the bike to be shifted and works with open dropout and thru-axle frames up to 12mm.
$19.95
Park's Home Mechanic Pedal Wrench is great for your home workshop and event tool box. This top-quality 15mm pedal wrench provides the leverage you need to remove stubborn pedals. It's made to last from heat-treated steel, and the handle has a vinyl grip for comfort.
$16.99
Many chains use a master link that allows the chain to be installed and removed by hand. While master links don't require traditional chain tools, over time, dirt and corrosion can make it difficult to separate them by hand. Park's Master Link Pliers make removing and installing these master links quick and easy. Simply insert the specially sized jaws into the link and squeeze the vinyl-coated handles!
$16.99
Park Tool's CTP-4K includes four replacement chain tool pins and one 5/32" ball bearing. To replace the chain tool pin, unscrew the cap, and pull out the old pin. Use care not to lose the ball bearing beneath the pin. Install the new pin and replace the cap. Works with the CT-4.3, CT-4.2, CT-4, and CT-11
$15.99
Park's Compact Crank Puller is used to remove Shimano Octalink, ISIS Drive and square-taper cranksets. It includes 2 rotating tips (16.3 and 11.3mm) to make the job easy. This is a great tool for your travel and home tool kit.
$15.95
The BBT-16 removes and installs the self-extracting/one-key release caps on SRAM and RaceFace cranks with a 16mm hex hole. Features investment cast steel construction and an option to use 8mm hex for better leverage.
$12.95
Park Tool's SW-11 is a forged, double-ended spoke wrench designed to fit select Campagnolo wheels. Precision machined, plated and vinyl dipped for comfort and long life. It fits Campagnolo 5.5mm and 6.0mm hex spoke nipples.
$12.95
Park's Spoke Wrench For Shimano Wheel Systems is the right tool for the job. It's made of durable tool steel and features 4.4mm and 3.75mm openings to fit all Shimano Wheel System nipples located at the hub and at the rim. It's vinyl-coated for a great grip, too.
$10.95
Park's Hex Wrench Set offers all the popular Allen wrenches (1.5, 2, 2.5, 3, 4, 5 and 6mm) in a convenient fold-up unit. The tool tips are chamfered for a positive grip and the one-piece fiber-reinforced-resin handle is light, comfortable, slip resistant and 40% stronger than steel.
$10.95
• Updated to fit better in the hand with a more rounded, smoother shape • The precision sized SW-7.2 fits the three most popular spoke nipple sizes on the market • Nickel plated for years of service • Designed for the home mechanic. FIts the following size spoke nipples: • .127" (3.23mm) • .130" (3.30mm) • .136" (3.45mm)
$9.95
Park's Bladed Spoke Holder is a must for building and truing wheels that feature bladed spokes. It has 4 different size slots to fit a wide variety of bladed (aero) spokes from .08 to 2mm wide. It holds them safely in place to prevent twisting as you turn the nipple to true and tension the wheel.
$9.95
Heat-treated alloy tool steel, one inch base fits wrench or bench vise. Thin-wall construction allows use without removal of cones and locknuts. The FR-5 has 12 splines that are approximately 23.4mm across. - Fits Shimano, SRAM, Sunrace, Suntour, Chris King and other cassette lockrings - Fits the SRAM XX1 11-speed cassettes - Also fits Shimano disc brake lockrings - Always use a quick-release skewer to hold the tool in place and snug to cogs when loosening; for solid axles, use the axle nut
$9.95
Park's Cone Wrenches are made of durable tool steel and are nice and thin to fit on the small-clearance cones found on hubs and other bearing assemblies. Plus, they work as regular wrenches, too. They feature Park's special Y heads that put more material where it's needed for excellent durability and strength. This 24mm wrench fits Shimano 15mm through-axle front hubs and many suspension-fork top caps. Some applications require at least 2 cone wrenches. If you have questions please contact us and we can recommend the correct sizes for your needs.
$8.99
12 splines, 22.6mm diameter fits Shimano, Sachs Aris, Sun Race, DNP Epoch, and other 5–10 speed freewheels. The FR-1.3 includes an enlarged thru-hole to accommodate 14mm axles.
$8.95
Park's Double-Ended Cone Wrenches are designed for home mechanics. They're made of thin tool steel to fit the low-clearance adjusting nuts and cone flats on a variety of bearing assemblies. Each wrench is chrome plated for long life and available in popular combinations from 11 to 18mm. Most applications require a pair of cone wrenches. Call or stop by. We can recommend the correct sizes for your needs.
$7.99
Park's FR-1.2 Freewheel Remover fits Shimano freewheels made since 1985. It's built thin so that removing axle parts is unnecessary. And, it's constructed of durable heat-treated steel.
$6.95
Park Tool's Derailleur Clutch Wrench is a small, thin wrench with 5.5mm and 3mm openings designed to fit the rear derailleur clutch tension adjuster on Shimano XT, SLX, Deore, Saint and Zee rear Shadow Plus (+) derailleurs and all previous Shadow Plus models.
$5.99
Park Tool's Pump Rebuild Kit contains one #1081 head as well as one #1087 plunger gasket for their PFP-3, PFP-6 and PFP-8 floor pumps.
Page 1 of 2 Next page